Assembly Figure more than 200 hours of modeling Consists of 41 pieces. Each piece is less than 14 cm to allow all printers to print all the files have been decimated by the polygons, but without losing the details, this makes the light files suitable for each computer

dimensions approximately L 94 Cm H 24 Cm W 14 Cm
L 37 inch H 9,4 inch W 5,5 inch

all files are already in place for optimal printing

The bridge 3D model was designed to get a clean print result, without considering printing material consumption, However, you are free to rotate, or scale, every part of the model in the most convenient way for you. Each file has been checked and repaired with Netfabb The parts of the model are already positioned for 3D printing Compatible with every Slicer- Simplify3D, Care, Slic3r, etc ... All the parts of the model have been cut so as to be printed vertically, for a higher quality of printing

The Francis Scott Key Bridge, also known originally as the Outer Harbor Crossing, sometimes simply referred to as the Key Bridge or Beltway Bridge, was a continuous steel arch bridge spanning the Patapsco River and the Harbor of Baltimore, Maryland. It constituted a section of Maryland Route 695. The main span, 366 m long, was the third longest in the world among those with a continuous girder[1]. It was also the longest bridge in the Baltimore metropolitan area. Built starting in 1972, the bridge opened to traffic on March 23, 1977 and was named after Francis Scott Key, author of the American national anthem. The bridge was the outermost of Baltimore Harbor's three toll crossings (two tunnels and one bridge). Once completed, the bridge structure and its ramps became the final links of Interstate 695 (the "Baltimore Beltway"), completing a two-decade project. Despite the I-695 signage, the bridge was officially considered part of the state highway system and was designated Maryland Route 695.

On March 26, 2024, around 1:30 am, the bridge collapsed following the collision of the Dali cargo ship with one of the pillars supporting it Wikipedia

Recommended settings for printing

each part was cut to be printed vertically, to have a better quality print, so for the upper parts, it is recommended to print with a 4-5 skirt

Quality Layer height: 0.1mm* Initial layer thickness: 0.3mm Bottom/top pattern: lines Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers). *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.

As a STL file provider, our goal is to ensure that the files are error-free and printable in the most accurate way. This is why we only test print the most difficult segments of the model’s parts.

The model's parts have been tested and printed in PLA. In case you need advice where to get your filaments from, check our partner's website.

Speed setups: Infill speed: 30mm/s Outer shell speed : 30mm/s Inner shell speed: 20mm/s Top/bottom speed: 20mm/s Support speed: 50mm/s Travel speed: 150mm/s Skirt speed: 30mm/s Amount of slower layers: 4 Infill:

Infill pattern: Grid Line distance: 1.5mm Infill overlap: 20% Infill layers: 0 Support:

Enable support: Check Placement: Everywhere Overhang angle: 30° X/Y distance: 0.7mm Top distance: 0.2mm Bottom distance: 0.2mm Stair step height: 0.5mm Join distance: 0.7mm Area smoothing: 0.6mm Use towers: check Pattern: Grid Line distance: 1.5mm

LEGAL PRIVACY POLICY: Any UNAUTHORIZED use of my profile, video, pictures or audio in any form or in a forum now or in the future is NOT permissible without my expressed written consent. Any act to promote or gain profit in any manner (e.g. either monetarily or socially) from the use of my profile, video, pictures or audio in any form my profile is a violation of my privacy and subject to legal action. BY WATCHING THIS: You acknowledge and agree that you shall not post, upload, publish, transmit or make available in any way content of this page including images and recording streamed live video available for download. This is intended as, and presented as a one time, live, one view presentation only. Penalties of Copyright Infringement: By reproducing, republishing or redistributing the work of a copyright holder without permission, you may be violating or infringing on his or her rights under the Copyright Act. The copyright holder may sue for compensation cost from $ 250 to $ 150,000 or one year jail sentence

You will get 2 files

All files previously purchased will always be available for download in your Library

Bridge H0 trains Baltimore bridge File 3D Printer

You will get 2 files

Similar products